Build My Camper: Hawk Flatbed Model

If you are looking for a side awning for your new Flatbed Camper, then this is the option you would choose. It is an 8' awning, mounted on the passenger side of the camper, and easily cranks in and out (manually).

Sometimes customers will need their mechanical campers jacks extended a few inches "wider" on each side of the camper for better clearance during loading & unloading of their camper from the truck. When customers have really wide fenders, dual rear wheel (dually trucks), wide over-sized truck tires, or putting a flat bed model camper on a flat bed truck, they sometimes need extension plates to get the camper jacks a few inches wider. This is not a common option. We only sell a few sets each year.

If you need to take your Flatbed Camper off of your truck from time to time, you would need to order these removable camper jacks. They come as a set of 4 (one for each corner of the camper), and can be easily attached to the camper, or removed while traveling. They operate manually by using a hand crank or a cordless drill with drill bit.

This is an available option for our Flatbed Model campers. It includes the rear wall rack, a set of MaxTrax  (portable stowaway extraction tracks), and Two (2) Rotopax Containers. The rack is constructed of lightweight aluminum. (Note: This rack is not intended for carrying bikes, spare tires, or really heavy items).

Looking to add some lightweight RotoPax or MaxTrax to the rear wall of your Flatbed Camper? Then you can consider ordering the "rack only" to start with and add your accessories as you go (at a later date). This rear wall rack is constructed with lightweight aluminum and attaches to the "jack brackets" on the rear corners of the camper. (Note: This rack is not intended for carrying bikes, spare tires, or really heavy items).

The Exterior LED Lighting Package is a great option if you are looking for more outside lighting  around your truck & camper at night. This option comes with 4 LED lights outside facing downwards towards the ground (1 light under teach corner of the camper). And on a separate switch, 2 LED side lights to light up both the driver's side & passenger side around your truck. The lights don't use much power and it makes getting around the campsite at night much safer.

If you are ordering a "Flat Bed Camper" you can choose the LED Flood Light option for either the rear wall, the passenger side wall, or both. This option would be to add LED Flood Lights on the Passenger Side of your new Flat Bed Camper.

LED Rear Flood Lights can be a nice addition to your camper if for are looking for the most possible light outside. These lights are typically used for short periods of time as bright utility lights. Examples on how customers will use their rear flood lights: unloading your horses at night, putting your boat in the water in the dark, scaring away unwanted critters in your campground at night, security issues, and many more uses not listed.

Looking for a simple, basic, inexpensive roof rack? The Aluminum Roof Rack we offer might fit your needs. It included the rear cargo rack and also a single cross bar near the front of the camper roof.

This option is for the complete Yakima Roof Rack System. It would include Yakima tracks installed on the camper roof, landing pads, towers, 2 cross bars , and locks.

Roof Rack "Tracks Only" installed on the camper roof. This option will allow you to easily add the complete Roof Rack System at a later date.

Looking for the most air circulation inside your camper? Then considering ordering the Extra Roof Vent. This extra vent will be installed over the cabover bed area. It is easy to open and close while you are in bed, making it convenient to cool down a hot camper, or close it when you get chilly without leaving your bed in the middle of the night. 

The power roof vent fan is an excellent option for hot weather camping. It is a "must have" option for most every camper we build. It's the next best thing to having an air conditioner inside the camper.

Powered Roof Vent Fan, Installed Forward (in the cabover portion of the camper roof / over bed area).

For customers that might want to install their own aftermarket solar panels, we can install a "Charge Controller Only" inside your new camper if you like. From there you can source and install your own solar panels at a later date. All campers are pre-wired for solar, but not all campers come with the controller installed, and the campers don't come with in-line fuses or a completed/hooked up solar wiring. If you by a solar system from us we will install everything and make the system turn-key. But if you decide to install your own solar panels at a later date there is still some work you will need to do to complete it all.

Overland Solar 130 Watt Portable Solar Panel without the charge controller.

Solar is becoming more popular each year. For customers ordering the compressor style refrigerators, or for customers that want to insure their camper battery(s) stay as charged up as possible will usually order the complete solar system with their new camper. This package includes the Overland Solar 160 watt roof mounted solar panel, the MPPT charge controller, wiring, in-line fuse, and the system will be ready to go when you pick up your camper. 

If you are ordering a Flatbed Model and want dual solar panels on the roof, we are now able to do this. This option would include 2 (two) 160 Watt Overland Solar panels, with a 30 amp MPPT charge controller. (Note: This is option is only available on the Flatbed Camper Models, and the Grandby Slide-in model, due to roof size restrictions). This option is not retrofitable at a later date by the factory. Must be ordered when we build your new camper.

Want more reserve power for your camper? Adding a second 12 Volt Battery (dual battery set up) will give you double the battery power, compared to having just 1 battery in your camper.

Dual 6 Volt Camper Batteries. This option will give you the most usable 12V power. Dual 6 Volt batteries will hold approx. 25% more power, compared to having dual 12 volt batteries.

All of the new Four Wheel Pop-up Campers come standard with 1 (one) 12 Volt deep cycle camper battery and the battery separator. Customer can choose to upgrade to dual camper batteries if these choose to. The battery separator will automatically keep the truck starting battery, and the camper battery, separate from each other while you are camping. This ensures your truck will always start, even if you have some how accidentally drained the camper battery(s).

Dual Lithium Batteries for your new Flatbed Camper with upgraded electrical system.

Dual Lithium Batteries for your new Four Wheel Camper.

On Slide-In Models, the Lithium battery option is only available on the "Front Dinette" floor plans.

Dual Lithium Batteries AND Dual 160 Watt Roof Mounted Solar Panels.

The Hot Water & Outside Package includes the 6 gallon hot water heater w/ DSI (direct spark ignition) and the outside shower feature. You will also be able to use hot water at the inside sink with this options.

For customers that might want the built-in Cassette Toilet installed in their Flatbed Camper (but no inside shower), this would be the option to select. Having hot water & and the outside shower is still an option, but you would also need to select that particular option as you are building out your camper order.

Some customers would like the Inside Shower installed in their Flatbed Camper, but do not want the cassette toilet built in. This would be the option you wound want to choose in that case. By choosing this option your new Flatbed Camper would come with the hot water heater, an inside shower, and the outside shower (but no built-in cassette toilet).

The Forced Air Furnace is our most popular option. Having a furnace is the best option for customers camping in colder weather. Early Spring, Late Fall, or in the Winter, having a warm furnace that is safe & comfortable to use is highly desirable to our customers.

The "Interior Only" Silver Spur Package includes the dark grey & light grey formica cabinets and Dovetail Greystone Fabric.

All of the new Four Wheel Campers come standard with the traditional wood grain interior look (maple wood color). This has been a popular interior choice for our customers over the years. It has a bright & warm feeling to it. Lightweight, durable, and no additional charge (it is built into the base camper price). There are many different interior fabric colors for you to choose from.

The Suburban 2.7 cu.ft. Refrigerator/Freezer is a Gas Absorption style refrigerator and can be run on 3 different modes (120V AC shore power, 12V battery power, or propane) The biggest benefit to a gas absorption refrigerator is that is can be run on propane the entire time you are camping, and won't drain your camper battery(s) down. It can run (cool) the refrigerator using propane. But that said, this style of refrigerator does have to be perfectly level in order to work properly, and these refrigerators do unfortunately have a hard time cooling in hot weather conditions (95 degrees F, or hotter).

The Isotherm 65 Liter Refrigerator/Freezer is a compressor style refrigerator unit that runs on either 12 volt battery power or 120 volt shore power electricity. This refrigerator does NOT run on propane.  The benefits to a compressor refrigerator like this, is that is does not need to be level to work properly, once you turn it on, it works, and it usually will cool more efficiently in hot weather. But you will need a dual battery system and a roof mounted solar panel to keep up with the power it uses. Without dual batteries and a good solar system, this style of refrigerator will drain your camper battery down in about 1 day.

The Isotherm 85 Liter Refrigerator/Freezer is a compressor style refrigerator unit that runs on either 12 volt battery power or 120 volt shore power electricity. This refrigerator does NOT run on propane.  The benefits to a compressor refrigerator like this, is that is does not need to be level to work properly, once you turn it on, it works, and it usually will cool more efficiently in hot weather. But you will need a dual battery system and a roof mounted solar panel to keep up with the power it uses. Without dual batteries and a good solar system, this style of refrigerator will drain your camper battery down in about 1 day. But you will need a dual battery system and a roof mounted solar panel to keep up with the power it uses. Without dual batteries and a good solar system, this style of refrigerator will drain your camper battery down in about 1 day.

The Isotherm 130 Liter Refrigerator/Freezer is a compressor style refrigerator unit that runs on either 12 volt battery power or 120 volt shore power electricity. This refrigerator does NOT run on propane.  The benefits to a compressor refrigerator like this, is that is does not need to be level to work properly, once you turn it on, it works, and it usually will cool more efficiently in hot weather. But you will need a dual battery system and a roof mounted solar panel to keep up with the power it uses. Without dual batteries and a good solar system, this style of refrigerator will drain your camper battery down in about 1 day.

All of the Base Model campers come standard with the smaller gas absorption refrigerator. These small 3-way "refrigerators only" can be run on shore power 120V electricity (when you can plug your camper in somewhere), 12 volt battery when you are driving, or by propane. Choosing the correct refrigerator for your camping needs is important, so please have a longer conversation with your sales person or your factory rep. on what size & style of refrigerator will be best for you.

For customers wanting modern appliances and more counter space, the Flush Mount Sink & Stove upgrade is very popular. The sink & stove are recessed into the countertop giving you more usable counter space.

This is a picture of the standard Sink & Stove that comes on our Flatbed Models. These are standard equipment and are built into the base model camper pricing.

Each customer seems to have a different preference on how to get in & out of their Flatbed Model camper. This option would be for the Aluminum Accordion Scissor Entry Steps that attach to the side of the camper. Flatbed truck & camper combos will usually take the Five (5) Step Version for the proper height and angle of the steps when set up. But please check with your sales rep or dealer on what number of steps would be best for your truck height. The accordion steps are available in several different versions (4 step, 5 step, and 6 step) and prices vary.

Axe & Shovel Kit Combo. This option attaches to the rear wall of the camper (to the jack bracket on the corner of the camper).

Back-up cameras are available for Factory Direct camper orders, and many of our individual dealers offer these as an option as well. These aftermarket backup cameras are available for most trucks, but not all. Your truck needs to have a factory installed camera already for our camera to work properly.

The "Carpet Kit" option is a custom made piece of carpet to lay over the standard linoleum floor. All campers always come with the linoleum flooring, but if you want something nicer and more comfortable, a carpet kit is a nice touch. Some customer feel that it helps to keep the camper cleaner inside, as the carpet allows dirt to settle and can be swept out when you get home from your camping trip. The carpet is removable for easy cleaning.

Looking for the largest cabover bed inside your camper? Or maybe you would prefer to sleep North/South (front to back) up in the cabover bed? Then please consider the "King Slide-out" for the cabover bed in our Full Sized Campers, and in some of the Flat Bed Models as well. (Note: The smaller Swift & Fleet Models already offer the North/South sleeping arrangements). Also please make note: Hawk & Raven Models with the Roll Over Couch Seating or the Side Dinette Seating floor plans also require the customer to choose the "Flush Mount Appliances" option.

This starter package includes the following options ... 5 gallon gray water storage bag (for containing the sink waste water), the standard propane tanks “purged” for the first time and filled with propane for you. (This package does not include extra propane tanks), 1 non-toxic fresh water filler hose, 1 bottle of Product 303 Protectant (Vinyl protectant for “pop-up” portion of camper), 1 bottle of Product 303 Wash (Camper cleaner for washing the outside of your camper), a water pressure regulator (for hooking up camper to city water), the 120V electrical extension cord (for plugging camper in to a campsite or generator), and extra fuses (small bag of assorted extra 12v fuses for emergencies).

If you order a roof rack and want better access to load & unload items off of the camper roof, you might want to consider adding the Side Wall Steps to your Flat Bed Camper order. Besides giving you better access to the roof, the side wall steps are also useful for hanging towels & swimsuits on, as well as many other things. With this option we will install Four (4) Side Wall Steps on the Passenger Side of the Flat Bed Camper.

If you like more comfort or like to camping in cooler weather conditions, the Thermal Pack is a great option for you. The camper will be warmer inside when you have the Thermal Pack option installed, the camper will stay a bit darker in the morning when the sun is coming up, and it is also a good sound barrier in case you have noisy neighbors at the campsite next to you. The Thermal Pack can be left in the camper year round, removed when you want, and the camper roof will still go up and down when the thermal pack is installed.

Each customer seems to have a different preference on how to get in & out of their Flatbed Model camper. This option would be for the Aluminum Accordion Scissor Entry Steps that attach to the side of the camper. Flatbed truck & camper combos will usually take the Five (5) Step Version for the proper height and angle of the steps when set up. But please check with your sales rep or dealer on what number of steps would be best for your truck height. Full sized, lifted trucks might need this "6 step" version. The accordion steps are available in several different versions (4 step, 5 step, and 6 step) and prices vary.

Ordering a Flatbed Camper? Want just a little extra seating space? Then maybe consider adding the Water Tank Cushion. This will give you a comfortable temporary space to sit over the front water tank area.

Back-up cameras are available for Factory Direct camper orders, and many of our individual dealers offer these as an option as well. These aftermarket backup cameras are available for most trucks, but not all. Your truck needs to have a factory installed camera already for our camera to work properly. This more expensive (complex) back-up camper is for the newer trucks with the 360 degree view cameras.

We sell and install Aluminum Flatbeds here at Four Wheel Campers. We are a stocking dealer of the Norweld UTE Alumimun Flatbeds (trays). Please ask your sales rep for more prices, options, and details if you would like to buy a Flatbed Tray, along with your new Flatbed Camper. If your truck already has a flatbed installed, we will charge Time & Materials to install your new camper on it.

For customers buying a Flatbed Camper, we now carry the Norweld Aluminum Flatbed trays. We can sell you the tray and you can install it yourself, or we can sell & install the flatbed tray & flatbed camper for you as a package. Most customers prefer their dealer or the FWC factory does the complete installation of the Flatbed tray and the Flatbed camper on their truck. Most of our dealers have Flatbed trays available and can supply you with pricing upon request. If you are ordering your new camper through one of our authorized FWC Dealers, you would want to work with them directly to order the flatbed tray from them as well.

CleanWaste Portable Toilet.

Thetford 260B Porta Potti.